Extron-electronic VersaTools MTP Series Manuale Utente Scaricare il pdf

Setup Guide — MTP Series

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Setup Guide — MTP Series, cont’d

68-732-50

Rev. B 02 09

Po wer Supply

Output Cord

SECTION A–A

Ridges

Smooth

A A

Captive

Screw

Connector

Tie Wrap

16 (5 mm) Max.

Example of a typical MTP S-video and audio application

Reserved / Chroma+

Reserved / Chroma-

Mono audio+

Video- / Luma-

Mono audio-

Reserved

MTP signal

Composite / S-video

Video+ / Luma+

Wire color

White-green

NOTE If you are using Enhanced Skew-Free™ A/V cable,

use the TIA/EIA T568A standard only.

NOTE The pin assignment is different if you have shifted

the jumpers in “Pre-installation — Jumpers” above.

Refer to the MTP Series User’s Guide.

Green

White-orange

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

White-blue

Green

White-brown

Brown

Blue Blue

Insert

TP Wires

Pins:

12345678

Step 4 — Receiver outputs

• Plug a video display into the applicable output connector:

 S-video output connector — A 4-pin mini DIN (Y/C) connector

 Composite video Input connector — A female BNC connector

• Plug an audio device into the applicable audio output connector:

 Two RCA connectors

 5-pole captive screw connector — Wire the connector as shown below.

C Connect the sleeves to ground (Gnd). Connecting the sleeve to a negative (-)

terminal will damage the audio output circuits.

INPUT

S-VIDEO

INPUT

VIDEO

L R

Unbalanced Stereo Input

Balanced Stereo Input

(high impedance)

Ring

Sleeve (s)

Tip

Sleeve

Tip

Sleeve

Tip

Ring

Do not tin the wires!

Mono

Stereo

Jumpered for

Mono (Default)

This card provides quick start instructions for an experienced

installer to set up and operate any of the MTP A/V

transmission systems.

Pre-installation — Jumpers

The units are factory-set to handle mono audio and

so that one unit cannot remotely power another.

They can be set to handle stereo audio and provide remote power.

A stereo audio unit is only compatible with older generation units.

The jumper blocks’ appearance and location change with each unit.

Refer to the MTP Series User’s Guide to set the jumpers for the unit(s)

to be installed.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the MTP tansmitter and

receiver as required.

Step 2 — Transmitter inputs

N The drawings at right show the available connections. Your unit may look different.

• Plug a video source into the applicable input

connector:

 S-video output connector — A 4-pin mini DIN

(Y/C) connector

 Composite video Input connector — A female

BNC connector

• Plug an audio source into the applicable audio input

connector:

 Two RCA connectors

 5-pole captive screw connector — Wire the connector as shown below.

Step 3 — TP cables

between units

Terminate a TP cable as shown

at right. Connect it between the

transmitter’s Output port and

the receiver’s Input port.

MONO AUDIO

Unbalanced Output

Balanced Output

Do not tin the wires!

Mono output 1-

Sleeve(s)

Mono output 1+

Mono output 2+

Mono output 2-

Sleeve(s)

Mono output 1

Mono output 2

NO GROUND.

SHARP

C GAIN

Y GAIN

SHARP

GAIN

S-video Receiver

Composite Video

INPUT

MTP T SV A RCA

VIDEO OUTPUT

L R

12V

0.5a

MAX

OUTPUT

SHARP

L R

INPUT

VIDEO

12V

0.5a MAX

MTP R SV A

XPA 1002

1 2

LIMITER/PROTECT

SIGNAL

OVER

TEMP

MTP T SV A RCA

Twisted Pair

Transmitter

MTP R SV A

Twisted Pair

Receiver

TP Cable

(up to 1,000')

DVD Player

Flat Panel

Display

Extron

SI 28

Surface-

mount

Speakers

Extron

XPA 1002

Audio Powe

Amplier

Step 5 — Power

Wire the 2-pole captive screw connectors for the included

external 12 VDC power supplies as shown at right. Plug them

into both units.

Step 6 — Receiver’s Sharpness and Gain

• Sharpness—Adjusts the output image sharpness for long

cable runs.

• Gaincontrol—Adjusts the brightness of the output image to

compensate for long cable runs.

 S-video receivers — There are separate controls for

luminance (Y) and chrominance (C). If the chrominance

setting is too low, the image may appear in monochrome.

Adjust the S-video gain until color appears.

 Composite video receivers — There is only one gain control on composite video

MTP receivers.

N The control knobs are removable to limit access if desired.

Setup Guide — MTP Series 1

Sommario

Pagina 1 - Setup Guide — MTP Series

Setup Guide — MTP SeriesExtron USA - West Headquarters+800.633.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAXExtron USA - East+800.63

Commenti su questo manuale

Nessun commento

Extron-electronic VersaTools MTP Series Manuale Utente

Navigare online o scaricare Manuale Utente per Hardware Extron-electronic VersaTools MTP Series. Extron electronic VersaTools MTP Series User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Hardware Extron-electronic VersaTools MTP Series